Cable A3W4.

TM 11-6625-2398-15-2

(21) Attach dust cover to link chain attachment.

(23) Attach dust cover to cable, using cable

m. Cable A3W4.

The following procedure is

clamp.

n. Cable 1A3W5.

The following procedure is

applicable to the replacement of connectors P1 and P2.

(1) Cut a section of cable (CP 5235A) 72

(1) Cut a section of cable (CP5263A) 71 1/4

inches in length.

(2) Strip 6 inches of outside jacket from end

(2) Strip cable in accordance with dimensions

of cable (fig. 7-10, dimension A).

shown in figure 7-19.

(3) Trim 5 1/8 inches of braid from end of

(3) Place the tag marker and one 8 3/4-inch

cable leaving 7/8 inch of braid exposed (fig. 7-10,

piece of heat shrink sleeving, three 5/4-inch pieces of

dimension B).

sleeving and one 6 1/2-inch piece of sleeving over

(4) Place tag marker and one 7-inch piece of

outside of cable jacket.

heat shrink sleeving over outside of cable jacket.

(4) Slide inner ground-ring over cable wires

(5) Slide inner ground ring over cable wires

and under cable braid.

(5) Slide outer ground ring over cable wires

(6) Slide outer ground ring over cable wires

and braid so that outer ground ring is centered over inner

ground ring.

(6) Cut a 9-inch length of 22 AWG black wire

(7) Cut a 6-inch length of 22AWG black wire

and strip inch of insulation from one end.

(7) Hairpin the black wire and insert between

(8) Hairpin the black wire and insert between

outer around ring and cable braid.

outer ground ring and cable braid.

(8) Using crimping tool, crimp outer ground

(9) Using crimping tool, crimp outer ground

ring, black wire, and inner ground ring.

(9) Install solder sleeves for double and single

(10) Strip 4 1/2 inches from jacket of twisted

shield coaxial cables as shown in figure 7-20.

shielded pair (fig. 7-10, dimension C).

(10) Disassemble either new or salvaged

(11) Trim 4 3/16 inches from braid of twisted

connector/ backshell assembly (fig. 7-17).

shielded pair (fig. 7-10, dimension F).

(11) Using crimping tool, crimp pins supplied

(12) Using crimping tool, crimp on ferrule and

with connector onto exposed wire ends.

ground wire (fig. 7-11).

(12) Slide the 6 1/2-inch piece of heat shrink

(13) Place an appropriate length of insulation

sleeving past the outer ground ring and shrink the

over ferrule and ground wire.

sleeving.

(14) Strip 3/16 inch of insulation from the end

(13) Sequentially slide the three pieces of 5

of each wire in the assembly (fig. 7-10, dimension E).

inch sleeving past the outer ground ring then shrink the

(15) Disassemble either new or salvaged

sleeving.

connector/backshell assembly (fig. 7-17).

(16) Using crimping tool, crimp pins supplied

NOTE

with connector onto exposed wire ends.

Before pinning connector P1, make

(17) Place a 4-inch piece of heat shrink

certain the connector cover is

sleeving over pinned wires and butt against outer ground

attached.

ring and shrink.

(14) Insert pins into connector (fig. 6-15) and

NOTE

fill open pin apertures with spare pins.

Before pinning connector P1, make

(15) Assemble connector / backshell assembly

certain the connector cover is

to cable (fig. 7-17).

attached.

(16) Coat strain relief and cable end with

thermofit adhesive and slide 8 3/4-inch piece of heat

(18) Insert pins into connector (fig. 6-14) and

shrink sleeving over coated area.

fill open pin apertures with spare pins.

(17) Using heat gun, shrink sleeving.

(19) Assemble connector / backshell assembly

(18) Remove excess adhesive from strain relief

to cable (fig. 7-17), making certain connector is properly

and sleeving.

oriented.

(19) Shrink the tag marker.

(20) Coat strain relief and cable end with

(20) Attach dust cover to cable using cable

thermofit adhesive and slide 7-inch piece of heat shrink

clamp.

sleeving over coated area.

o. Cable 1A4W1.

The following procedure is

(21) Using heat gun, shrink sleeving.

(22) Remove excess adhesive from strain relief

applicable to the replacement of connector P1 and P2.

and sleeving.

(1) Cut a section of cable (CP5225) 71 1/2

inches in length.

7-12