C2, TM 11-6625-1683-15
(b) Perform a leakage test from each
Perform a leakage and high-pot
(b)
pin of P1 and P2 to all other pins
test from each pin of P1 to all
of PI and P2 and to the hoods of
other pins of P1 and to the con-
P1 and P2. The leakage should be
nector hoods. Leakage should be
greater than 10 megohms.
greater than 10 megohms. High-
(c) Perform a high-pot test between
pot at 500 volts ac for 1 minute
each pin of Pl, except pin 13, and
except P 1 9 , which should be
all other pins of P1. A potential
high-potted to other pins and hood
of 3 kilovolts ac should be applied
at 1,000 volts ac for 1 minute.
for 1 minute. Apply 6 kilovolts ac
(15) C X - 1 0 4 4 0 PPS-5 cable assembly
between pin 13 and each of the
(block 2300).
other pins of PI for 1 minute. A
potential of 500 volts ac should be
each pin of P1 and the correspond-
applied between each pin of P2
ing pin of P2. Use the RX1 range
and all other pins of P2 for 1 min-
on Multimeter ME-26(*)/U. The
resistance should be less than 0.1
ute.
( 1 2 ) C X - I 0 4 W P P S - 5 cable assembly
ohm.
(block 2700).
(b) Perform a leakage and high-pot
test from each pin of P1 to all
each pin of PI and the correspond-
other pins of P1. Leakage should
ing pin of P2. Use the RX1 range
b e greater t h a n 10 megohms.
on Multimeter ME26 ( * ) /U. The
T e s t s between pin S and other
resistance should be less than 0.1
pins should be made with 6 kilo-
ohm.
volts ac applied for 1 minute.
(b) Perform a leakage and high-pot
( 16) CX-10445 PPS-5
cable
assembly
test from each pin of P1 to all
(block 400).
other pins of P1. Leakage should
each pin of PI and the correspond-
be greater than 10 megohms. High-
ing contact of J1. Use the RX1
pot at 500 volts ac for 1 minute.
(13) C X - 1 0 4 3 8 P P S - 5 cable assembly
range on Multimeter ME26 ( * )/
(block 2900).
U. The resistance should be less
than 0.1 ohm.
each pin of P1 and the correspond-
(b) Perform a leakage and high-pot
ing pin of P2. Use the RX1 range
test from each pin of P1 to all
on Multimeter ME26 ( * ) /U. The
other pins of P1. Leakage should
resistance should be less than 0.1
be greater than 10 megohms. High-
ohm.
pot at 500 volt ac for 1 minute.
(b) Perform a leakage and high-pot
(17) CX-10445 PPS-5 cable assembly
test from each pin of P1 to all
(block 500).
other pins of P1. Leakage should
be greater than 10-megohms. High-
each pin of P1 and the correspond-
pot at 500 volts ac for 1 minute.
ing contact of J1. Use the RX1
(14) C X - 1 0 4 3 9 P P S - 5 c a b l e a s s e m b l y
range on Multimeter ME26 ( * )/
(block 700) .
U. The resistance should be less
than 0.1 ohm.
(b) Perform a leakage and high-pot
each pin of P1 and the correspond-
ing pin of P2. Use the RX1 range
test from each pin of P1 to all
on Multimeter ME26 ( * ) /U. The
other pins of P1. Leakage should
resistance should be less than 0.1
be greater than 10 megohms. High-
ohm.
pot at 500 volt 9 ac for 1 minute.
8.1-13
Previous Page
